This a very interesting project - very good work and many thanks for sharing with us your way of solving these technical problems
-
Win a Free Custom Engraved Brass Coin!!!
As a way to introduce our brass coins to the community, we will raffle off a free coin during the month of August. Follow link ABOVE for instructions for entering.
Colin Archer RS 1 anno 1893
- Thread starter Woodcarving Reidar
- Start date
- Watchers 8
Got the steel keel fixed today. It cost 300, - kr.
New weight is 9.3 kg
And oak materials were also finished. dimension:
12, 10 and 6 mm to the frames. IT cost 800,- kr
will start by shaping the underside of the keel tomorrow
New weight is 9.3 kg
And oak materials were also finished. dimension:
12, 10 and 6 mm to the frames. IT cost 800,- kr
will start by shaping the underside of the keel tomorrow
Last edited:
I was lucky enough to stay with someone in the family today. Used 5 angle grinder blades 125 mm
had to buy with a small plane grinder also to smooth out the balls that you get with only angle grinder. Unfortunately, the motor on the plane grinder is a little too small, so I have to be patient. will continue to cut on the steel keel tomorrow
New weight is 7,5 kg
had to buy with a small plane grinder also to smooth out the balls that you get with only angle grinder. Unfortunately, the motor on the plane grinder is a little too small, so I have to be patient. will continue to cut on the steel keel tomorrow
New weight is 7,5 kg
We can see, that you used safety cloths / gloves for your hands....
But what did you do for the safety of your bare feet?
Could get hot .....
But what did you do for the safety of your bare feet?
Could get hot .....
then I made a sledge in which the metal keel was placed. it helps when drilling holes for M4 mm bolts. it went with 12 pcs. I also finished the template on top so I have something to cut the keel after. also had to notice the underside since it is narrower there
That plate on top is only temporary as a template
Top
underneath
That plate on top is only temporary as a template
Top
underneath
Last edited:
very funny.
The explanation is that the picture is taken from the hallway. tend to go barefoot inside
new update.
has left a bit. so now the keel weighs 5.1 kg.
have some finishing touches to make it look the same on both sides. I've noticed how many mm I have to grind down. must also make a notch on the end of the keel. I don't think more will be done before January 2, 2020
has left a bit. so now the keel weighs 5.1 kg.
have some finishing touches to make it look the same on both sides. I've noticed how many mm I have to grind down. must also make a notch on the end of the keel. I don't think more will be done before January 2, 2020
Last edited:
Finish keel.
Of course I couldn't keep away from some model building today either
the weight of the keel stopped at almost 5.0 kg
Of course I couldn't keep away from some model building today either
the weight of the keel stopped at almost 5.0 kg
Last edited:
today was that I got the milling of slots for frames and preparation of the stem to cut it out tomorrow in 12 mm oak
unfortunately burned I a Dremel 4000, during milling of the tracks to the ribs, so I had to use a real router. bought a new Dremel today on offer.
unfortunately burned I a Dremel 4000, during milling of the tracks to the ribs, so I had to use a real router. bought a new Dremel today on offer.
Then the bottom was cut and ground. Now it is waiting for me to mill tracks for exterior cladding.
The parts for the fore and aft of the stem have been cut out on a band saw and refurbished. now I'll glue them together
The parts for the fore and aft of the stem have been cut out on a band saw and refurbished. now I'll glue them together