Swedish capital ship ca. 1700 – into the abyss of the Great Northern War

[-Waldemar-]

.​

The very launch of this thread has been made possible by the kind decision of curator Jonas Hedberg to make a recent 3D scan of the hitherto unidentified ship model Ö 6 from the collection of the Sjöhistoriska museet in Stockholm available for download. More information about this promising model can be found on the museum's website:

Fartygsmodell - Sjöhistoriska museet / DigitaltMuseum

And on the Sketchfab website:

Ship of the line, c. 1700 | Linjeskepp, ca 1700 - Download Free 3D model by SWEDISH NATIONAL MARITIME AND TRANSPORT MUSEUMS (@maritima) [3afea35] (sketchfab.com)

Many other relevant data, particularly useful for the identification of the model, can also be found in the major studies on the Swedish fleet and shipbuilding: Svenska Flottans Historia. II. 1680–1814. Örlogsflottan i ord och bild från dess grundläggning under Gustav Vasa fram till våra dagar, Malmö 1943, Svenskt skeppsbyggeri. En översikt av utvecklingen genom tiderna, Malmö 1963 and Karlskronavarvets historia. Del 1. 1680–1866, Karlskrona 1993.

Some views of the model Ö 6:

​

.​

 

[fred.hocker]

Good to see this model get some attention!

Fred

 

[-Waldemar-]

.​

Thank you Fred for entering. Honestly, at this point I'm in the abyss of trying to identify this model (at least its rate) before undertaking proper reverse engineering. It's always a good idea to scale it realistically beforehand. You can even actually help by checking any of its main dimensions, as after the case of the model Ö 3 (Naseby 1655/Riksäpplet 1663) I no longer have confidence in the dimensions given in Glete's study on ship models, apart from the fact that those given there again do not want to match other known data.

.​

 

[-Waldemar-]

.​

(Pre)identification

Taking into account the most relevant dimensional considerations, the specifications of the Ö 6 model (enlarged 33 times) were tentatively settled as follows:

Length between posts: 160 feet
Breadth (without planking): 40.5 feet
Draught: 19.5 feet
Distance of gun ports from the waterline: 5.5 feet
Height of lower battery deck: 7.5 feet
Width of gun ports (on lower battery deck): 3.5 feet
Distance between gun ports (on lower battery deck): 8.5 feet

​

The dimensions associated with the gun ports are appropriate for the largest system calibre in the Swedish fleet, at 36 pounds. Guns of this calibre were reserved for ships of the highest rates, as were four gun ports aft (as opposed to only two for ships of lower ranks). To the total number of gun ports should be added at least one gun port on each of the two battery decks, which on the presentation model apparently had to give way to the intended stern decorations (on this, see also the plan reproduced below). On the actual ship, it is also very likely that there were other additional guns on the highest decks that were not reflected in the model, of the smallest calibres and hardly of any tactical significance in the battle fleet.

As a kind of parallel, and for a comparison of some dimensions, crucial for determining the size of the ship represented by the Ö 6 model, a ship design from the same period is included below (Swedish archives):

​

Such characteristics of the Ö 6 model are most consistent with the rate and dimensions of two ships – Sverige 1679 and Prinsessan Hedvig Sofia 1692, as shown in the table below taken from Svenska Flottans Historia. II. 1680-1814, s. 546:

​

.​

 

[-Waldemar-]

.​

Before proceeding further, let us stay with the dimensions and scale of the Ö 6 model, or rather the size of the actual ship that this model represents. While it is true that one can search in vain in the archives for plans of Swedish ships from before 1700 for reference, however, invaluable Martes found in the Russian archives a plan of yet another vessel from this very period of activity of the same generation of shipwrights – Prins Karl Fredrik 1704 – which is particularly relevant to this case.

It is reproduced here together with the plan of Konung Karl 1694 (Swedish archives). Both ships were designed by Charles Sheldon (as was Nordstjärnan 1703, shown above), and both plans were already drawn retrospectively, even several years after the vessels were built, most likely by the same person. Despite that, the ships were many decades in active service and it can be thought that these later plans nevertheless represent their characteristics quite faithfully.

As can be seen, the parameters of the gun ports of the Prins Karl Fredrik 1704 perfectly match their dimensions on the Ö 6 model scaled earlier mainly on this basis, whereas in the Konung Karl 1694, while of the same width, they are more tightly spaced due to the need to pack as many as 106 guns on this vessel. Paradoxically, it was Konung Karl 1694 that was the ship armed with the heaviest, 36-pounder guns, while the others shown here had to practically make do with 24-pounder guns (see on this detailed data in Lars O. Berg, Karolinsk flotta. Studier och tabeller, [in:] Forum Navale 25/1970).

​

.​

 

[Martes]

Note that it the model is not the only case in contemporary Swedish models where the aftermost port on the main gun deck is omitted. See, for example
https://digitaltmuseum.se/011024799526/fartygsmodell

​

 

[-Waldemar-]

.​

Prearrangements

The noted distortions of the model are quite minimal, so the only prior correction to its shape was to slightly bend the hull sideways so that the sternpost was exactly in the axis of symmetry. In addition, for further shape testing, the hull was rotated to an even keel – after numerous fittings and preliminary measurements, this seems to be the most promising orientation.

The next step is to obtain the undisturbed outer contours of the frames by virtually 'stripping' the wales and any planking from the full height of the hull. To this end, cross sections were taken off the hull at 'strategic' locations, as shown in the attached images.

​

.​

 

[-Waldemar-]

.​

Actually, it was not my original intention to show the rather chaotic-looking working graphics, however, the Ö 6 model scan is revealing more and more of its secrets, and as a sort of curiosity I am demonstrating how the design shape of the line of the greatest breadth was found on the plan view.

To do this, the contours of all the frames were cut by a curved plane at the height of the line of the greatest breadth (found earlier), and then the intersection points were connected by a line (in blue). When this line was projected onto the plan view (thin red line), it was further set back in a parallel manner by the thickness of the planking at the corresponding height of the hull.

It appears that, taking into account the minor distortions of the model, it is possible to perfectly match for the fore part of the hull two types of curves: the combined curve of two circular arcs, commonly used until then by English designers (employed in Sweden at the time), and the logarithmic curve, known and used in turn for a long time already by continental designers, incidentally more flexible and more convenient in design terms. Both of them are shown on either side of the keel as thick black lines. In such a case, the choice of either of these two types of curve would necessarily have to be entirely arbitrary, were it not for the surviving designs of Swedish ships of the period indicating the first variant, that is, a curve combined from two arcs of circles.

For the aft half of the hull, the shape of the line of the greatest breadth is a perfect arc of a circle.

​

.​