-
Win a Free Custom Engraved Brass Coin!!!
As a way to introduce our brass coins to the community, we will raffle off a free coin during the month of August. Follow link ABOVE for instructions for entering.
Crypton, I just started this kit. Your completed model is beautiful; I hope I can do as well. The sails have a nice head-to-wind ripple look to them.
I am having trouble getting the frames to sit at the proper depth on the keel piece and square and level properly so as to fit on the initial rubbing strake(s) (red in your model). I need to get that right in order to place the tumbledown coaming properly aligned with the bevels. I've been through a number of disassemblies on various frames using alcohol to dissolve my white glue.
This is my first "serious" ship model. Did you need to do a lot of adjusting to get that part right? I do have a good flat table and various jigs and measurement tools but I don't think the keel and frames were cut very precisely. The plans are good though, in my opinion. Instructions, well not so much.
Any advice would be appreciated. Thanks.
I am having trouble getting the frames to sit at the proper depth on the keel piece and square and level properly so as to fit on the initial rubbing strake(s) (red in your model). I need to get that right in order to place the tumbledown coaming properly aligned with the bevels. I've been through a number of disassemblies on various frames using alcohol to dissolve my white glue.
This is my first "serious" ship model. Did you need to do a lot of adjusting to get that part right? I do have a good flat table and various jigs and measurement tools but I don't think the keel and frames were cut very precisely. The plans are good though, in my opinion. Instructions, well not so much.
Any advice would be appreciated. Thanks.
I remember struggling with this too. In the end I put the white border first and cover the gaps with the rubbing strakes. The white border was soaked and streamed to be able to fit it and glued with superglue/gel. Good luck with your model!
Thank you so much; it is reassuring to see that you struggled with that given that you are a Master modeler a la "Le requin". I looked at some of your other build photos; amazing!
When you say ""white Border" I assume you are speaking about the coaming pieces that are above the rubbing strake that you painted white?
I also thought about doing that procedure
Your advice has restored my faith in building this model correctly. Thank you again.
I chose this model because of a trip to Netherlands and my viewing the 'barge-style' Dutch boats. I consider them a unique design of a shallow watercraft, similar to the American 'catboat' for our shallow East coast bays.
Crypton, Can you tell me how you did the windows and skylights in your Mamoli Catalina? I see from your photos you did not use the blue material which is shown on the kit box. Your model's windows look much better and more realistic. I do not like the Mamoli kit blue plastic material method.
Thanks for any advice.
Thanks for any advice.
After over a year delay, I am back to building the Mamoli Catalina.
Now I must start the planking which is a challenge for a beginner like me.
I understand from reading and videos many of the techniques like using a planking fan.
However, I was wondering whether you started with the sheer or garboard plank, and whether you placed a mid-hull plank that forms a natural curve of the hull. (That is the technique of dividing the hull side into two zones.)
Anything you may remember would be helpful.
Thank you,
Best Wishes.
Now I must start the planking which is a challenge for a beginner like me.
I understand from reading and videos many of the techniques like using a planking fan.
However, I was wondering whether you started with the sheer or garboard plank, and whether you placed a mid-hull plank that forms a natural curve of the hull. (That is the technique of dividing the hull side into two zones.)
Anything you may remember would be helpful.
Thank you,
Best Wishes.
Although I do not remember the exact details, I think I used figure 26 from the manual as a guide. So from the rubbing lines work from the top center of the ship downwards. I thin down the width of the strips at the front and back of the ship. After getting stuck with bending the strips too much, switch from planking direction and start at the keel and work your way up. This will give you the typical two zones, you mention.
Good luck!
Good luck!
Crypton, thank you very much for the prompt reply and information.
It is very helpful to me.
It is very helpful to me.