Muscongus Bay Lobster Smack from Model Shipways by DocTom - Build Log

I am in the middle of building the lobster smack, my 3rd model. I was posting a build log on Model Ship World, now tragically gone. But you can't let the bastards win, so I continue here. I am at the point where I have started the process for priming and painting the hull. I started out by figuring where the water line should be. I used the plans in Chapelle's "American Small Sailing Craft" to try and figure out where it should lie. I think I came up with a good approximation.


I then masked off the deck



and applied the primer, oil-based from a rattle can. This revealed no major bumps or depressions, but many cracks - maybe from too aggressive sanding or beveling of the planks when I installed them? This was my first attempt at planking a POB hull, and I thought I had done a good job - amazing how some primer can humble the mighty!




Next step is to fill them. I've been using Occre crack filler, but plan to experiment with Durham's Rock Hard Water Putty, to see if I like it better. I plan to airbrush the hull. I have never used an airbrush, so I've been watching YouTube videos between building sessions.

Any insights/critiques would be greatly appreciated. I'm here to learn

Post 2 - Priming finished.

A quick update. I used Durham's Water Putty for the first time, and really liked it. I found it much easier to work with than the Occre putty - much less crumbly, and it sanded and feathered beautifully. I think I will use it from now on. After filling and sanding, I applied a second coat of primer. The port side looked pretty good



Some imperfections, but I think it will pass the 3 foot test. There were still some issues on the starboard side, so I applied more Durham's and sanded



I'll give that another swipe with the primer tomorrow, and pracitce airbrushing while it drys. My plan is to use the Model Expo Warm White and Hull Red supplied with the kit, and do the toe rail in the Hull Copper Red. Overall, I'm pleased with how my first attempt at fairing and planking a hull has turned out.

Very nice, smooth planking. I think some imperfections are perfectly warranty, or even expected as a working fisherman's boat.

Post 3 - Out of the Past

I thought I would try to recreate some of my build log of blessed memory, highlighting the issues and solutions I ran into that might be of help to someone else starting the Lobster Smack kit. I'll try to organize it by major tasks/areas of build. One thing I realized early on is that the model pictured in the instructions is not the model provided in the kit. It was clearly a prototype. Why can't they update the illustrations?

The central spine:
The first issue with the spine is that the pieces are very thin, and the water in wood glue can curl them. You need to weigh down the pieces as you glue them. I used the weightiest (in every sense) tomes I own


The other issue is that the pivot hole for the centerboard is incorrectly placed. There are several solutions to this. I decided to fill and move the hole, rather than widen the slot for the pull rod


The bulkheads:
My major problem was that my bulkheads all seemed too big compared to images in multiple build logs.




And it turned out they were. I contacted Model Expo Online, who sent me a replacement sheet. All the bulkheads were several mm shorter. By the time they arrived I had already glued and sanded down the bulkheads to fit.

The cockpit:
I tried my first attempt at kit bashing by scribing planks on the cockpit floor and deck. The main issue with the cockpit is the stern sheets are asymmetrical - clearly a fault with the laser cutting. I added a shim to the affected side, which isn't visible after I "stained" it with a thin wash of craft paint.


The deck:
Many build logs report decks that are too narrow, but mine was fine. I had to sand down the side of Bulkheads 3 & 4 where they protrude above the deck, and of bulkhead 2 to make space for the cabin walls.


Fairing and planking the hull:

This was my first attempt at fairing and planking a POB model. This was one of the thinks that always intimidated me about wooden ship models when I was younger - How did people know how to shape the curves? What I discovered, which I have found true of many things about modeling, is that what seems intimidating and complicated in the abstract becomes obvious when you have the wood in your hands. In the end, I really enjoyed the process - probably my favorite part of modeling so far. It appeals to my obsessive tendancies, and I find sanding and checking very therapeutic. I didn't understand, though, just how much wood you have to remove. Even though I thought I did a good job, and checked with artists tape and planks



I still had to do a lot more fairing of bulkheads 1, 8 & 9 when I started test fitting the planks. Planking took me almost 2 weeks. I could manage one set of strakes a day. The biggest issue with the preformed strakes is that they don't quite cover the hull, unless you faired it exactly like the prototype. I had to add stealers at the stern and bow to get the shear strake even with the deck. The other option would be to add a 10th strake.


Although the pictures make it look terribel, I was pleased with my first attempt at this process. After sanding and filling, it looked pretty good:



The coaming and cabin walls:

Adding the toe rails, rub rails and fairleads went according to instructions. Instead of forming the coaming and cabin walls on the model, I made forms from poster board, using the empty frets from the deck as patterns. I checked that my planking tool would not ignite the poster board!





They fit perfectly



I also "stained" the deck with a paint wash, folllowed by shellac.

The cabin roof and companionway:

On my model the indentation at the aft end of the companionway roof was too deep. I added a shim to compensate. I also raised the sliding hatch cover by 1/8" so it looked a little less two dimensional. I also cut down the cabin bulkhead so the companionway hatch would abut the sliding hatch. I stain/painted the hatches and painted the rails with Model Expo Hull Copper Red.


The beakhead:

As I said in my original build log, my beakhead as provided was a sad and droopy thing:



After mulling over options I elected to add shims to the bottom and rear



which left it looking much perkier



And that brings me back to the future.

Nice details. Documenting some of these issues is going to be invaluable for anyone building this kit in the future. It’s a shame that most of the logs for these three kits (the dory and the pram included) were lost in the MSW crash. I didn’t realize it was the single biggest collection of logs for them.

I don’t remember if you mentioned it in your other log, but how did you finish the deck? If I recall, you used an acrylic wash, it almost looks like a dory buff.

It's a very diluted wash of a DecoArt craft paint - Fawn, brushed on and then wiped off immediately (the Tom Lauria technique from YouTube), followed by two coats of amber shellac applied with a rag. I prbably could have just shellacked it.

Post 4 - A Quick Update

I've spent the past 5 days teaching myself the rudimentary techniques of using an airbrush. Lots of YouTube videos (Modelkit Stuff has a very helpful playlist) and lots of experimenting with different paint mixtures and air pressures. As a result, I've gotten very good a cleaning my airbrush! I bought an Iwata Eclipse CS (based on a recommendation from one of my fellow modelers on MSW), a Gaahleri Serenair table top compressor and a portable spray booth. Started off practicing on paper and cardboard with leftover paint from my Dory build. However, I wanted to test the two paints I will be using on my model, Model Expo Warm White and Hull Red. I have an extra set of bulkheads for the kit, so I primed and sanded two of them for a test run. I started off thinning them far too much, based on all the advice on YouTube. After much trial and error I ended up diluting the paint about 2:1 (two parts paint to one part water) with some flow improver thrown in. The results:







I think they came out pretty well, and I feel ready to put some paint on my smack tomorrow. This was the first time I ever used an airbrush, and I think I will enjoy using it, although I will clearly need to upgrade the compressor at some point.

In between airbrush sessions I managed to make my base.



That's it for now.

Very nice work!

Looking good! airbrush skills will surely be handy.

Maybe jumping in late, find the cracks inevitable because the bulkhead is curved and the plank face flat.

Filler can fill the crack, and the wood grain, leading to an uneven finish - wood has grain - filler does not. So minimize filler on the face of the plank by applying masking tape along the crack.

Put a glob of filler on wax paper, Take thin slices with an xacto blade and fill the cracks. Remove the tape, and a light sanding should do the job.

I embrace some small cracks, they let the viewer know the model is made of wood. Once showed my mom a fully filled in, primed and smoothed, then painted hull, she asked if it was plastic.

Find cracks are less visible when the hull is stained.

Your work is nice. Thanks Tom.

-Rich

Post 5 - Painting the hull

I spent the weekend painting the hull of my smack in between garden chores. After spraying on the Warm White and letting it dry for 24 hrs I marked the waterline using the jig provided in the kit.



This turned out to be the hardest part of the whole process. I had determined where the waterline should be on the hull before I primed it, based on the plans in Chapelle's book "Small American Sailing Craft," so the jig was at the appropriate height, but no matter what combination of rubber bands, shims and masking tape I tried, I couldn't get the model to sit level and stay still in the display stand. I finally ended up keeping it in a fixed position with one hand while scribing the line with the other. I measured the distance from the top of the toe rail to the waterline at several points to make sure it was symmetrical. I used Tamiya 5 mm tape for most of it, and 3M 3mm tape for the curve at the stern. Ended up with what I think is a close approximation of Chapelle's plan:





I then applied the Hull Red



I masked off the lower hull so I could paint the toe rail with the Hull Copper Red I had used on the sliding hatch rails. I again measured from the top of the toe rail at multiple points to make certain the masking was an even 3mm below the top of the rail.





After I nervously peeled back the multiple layers of tape, newspaper and paper towel I found this:







I need to do some touch up on the stem, and on inside of the toe rail, mainly at the bow where I just didn't spray it thoroughly.



As you can see, I also managed to break off the samson post, again! I think I will have to either drill hole for a metal pin, or ream out the hole and start over with a piece of hardwood - that probably makes more sense. As per instructions, I also remembered to pant the rudder!


This was my first time using an airbrush, and my first time painting a hull with two colors. I have to admit to being very pleased with myself! Once I figured out how to thin the paint properly (about 2 parts Model Expo paint to 1 part water with a few drops of flow improver) I found the airbrush quite easy to use. The whole process seemed very intimidating before I actually tried it, but now I feel I have overcome another of the mental hurdles I had created for myself, and have a new skill that will improve my modeling.

Now that I'm almost done painting, I get to go back to making things

Really nice work, that's a great paint job!

Crisp Waterline!

Lovely work. You tempt me to pull out my airbrush and try a new experience as well.

You should be very happy with that result!