see post #13 or #14
Ein Umbausatz incl. einem Einlageblech kostet 340.-€ Ein Sägeblatt 25.- €
A conversion kit including an insert plate costs € 340. A saw blade € 25
@Rablok
But as mentione before - one set is reserved for me when we meet in March
Ein Umbausatz incl. einem Einlageblech kostet 340.-€ Ein Sägeblatt 25.- €
A conversion kit including an insert plate costs € 340. A saw blade € 25
@Rablok
But as mentione before - one set is reserved for me when we meet in March
Is there any estimate on shipping to Eugene, Oregon, 97401 USA
340,-€+ 25 € für ein Sägeblatt
340,-€
It would be great to have but in pinching funds at this point I'll pass it by and say, "I should have", later. Rich (PT-2)
340,-€
REVIEW Conversion kit for Proxxon FET:
This afternoon I finally had time to mount the conversion kit on the Proxxon FET.
Got some support from Karl via email.
The cams of the old adjustment were ground, 4 M4 holes drilled, with this as a result:
When the knob A is loosened, you can adjust the guide bar over the round bar over greater distances. When you are near where you want to be, you tighten A. With the fine adjustment knob B, the guide bar has been turned against the saw blade:
Use the large black knob C to secure the guide bar to the saw table.
Set the digital meter to 0:
With the 2nd button from the left you switch between mm and inch.
A slat from the BN kit measured with the caliper:
4.23mm.
With the fine adjustment the guide bar turned to 4.23 mm:
And the slat fitted exactly between the saw blade and the guide bar:
Soon to actually use the FET.
And experiment with the digital meter. Because after a saw cut at a certain width, you can start again at 0 and continue measuring to the left or right.
Karl: Thanks for the support.
For the others: Is it worth the price? In any case, it will probably save a lot of fitting and measuring with the caliper. Now in the "Toys for Boys" category.
Regards, Peter
This afternoon I finally had time to mount the conversion kit on the Proxxon FET.
Got some support from Karl via email.
The cams of the old adjustment were ground, 4 M4 holes drilled, with this as a result:
When the knob A is loosened, you can adjust the guide bar over the round bar over greater distances. When you are near where you want to be, you tighten A. With the fine adjustment knob B, the guide bar has been turned against the saw blade:
Use the large black knob C to secure the guide bar to the saw table.
Set the digital meter to 0:
With the 2nd button from the left you switch between mm and inch.
A slat from the BN kit measured with the caliper:
4.23mm.
With the fine adjustment the guide bar turned to 4.23 mm:
And the slat fitted exactly between the saw blade and the guide bar:
Soon to actually use the FET.
And experiment with the digital meter. Because after a saw cut at a certain width, you can start again at 0 and continue measuring to the left or right.
Karl: Thanks for the support.
For the others: Is it worth the price? In any case, it will probably save a lot of fitting and measuring with the caliper. Now in the "Toys for Boys" category.
Regards, Peter
Ein Päckchen von <2 kg kostet 8,89 €.
Da der Wert unter 800 Dollar ist, fällt kein Zoll an.
vorrei acquistare completo set per fet sega proxxon digitale quando costa e compro subito con bonifico bancario urgente
I would like to buy the complete set for proxxon digital saw fet when it costs and I buy immediately with an urgent bank transfer
I would like to buy the complete set for proxxon digital saw fet when it costs and I buy immediately with an urgent bank transfer
Last edited by a moderator:
Ho bisogno kit della fet il mio email secondino.coccia60@hotmail.it dammi una risposta se hai da vendere sono italiano ok grazie
Hi 'coccia'.
Have you tried to send a PM to Karl? Or a e-mail, see his post #10 of #18?
Regards, Peter
Sorry to inform you, but Karl passed away appr. 1 year ago
Rablok alias Karl Schedelbauer
Hallo, I am sorry to inform you, that Rablok alias Karl Schedelbauer passed away some months ago. He was in Germany a very well known modeler and friend Here his french Napoleon in scale 1:75 https://shipsofscale.com/sosforums/threads/vaisseau-napoleon-m1-75.9472/ Rest in Peace my friend
shipsofscale.com
Thanks, Uwe. Then I am sorry to ........ I missed that announcement.
Regards, Peter