• LUCZORAMA SHIPWRECK SCAVENGER HUNT GIVEAWAY. 4 Weeks of Fun • 1 Legendary Prize ((OcCre’s Fram Ship)) • Global Crew Welcome!
    **VIEW THREAD HERE**

Constitution Cross Section MS20245 Model Expo

Were the fish to long, or did your compromise on mast length make it too short!
This discrepancy was also mentioned in the build by Tom Culb. I believe the mast length was also noted by him. I cut the "Fish" a bit shorter to fit the deck surround. The mast I made is actually a bit longer than the instructions would have you make, so the length of the "fish"as instructed is definitely too long.

Rob
 
The fighting top is looking good, but I never understood why all the wood was on top, where sailors stood, versus underneath. I know there was a crosstree that it sat on, but all the edges of raw wood and mostly bare feet, seems like it would be hard to stand firm in a rough sea!

Do the plans say where the saved piece will be used later?
I agree, I had the same thought. Hopefully the wood was smooth and sealed. Perhaps it was actually advantageous to have the wood there to stand between during rough seas?

I believe they just want you to save that piece to aid in the markings of the timbers. I do not think it has another use. Of course I will definitely keep it. (I have a pile of good from previous kits that annoys the Admiral, but you never know when you will need a piece!)

Rob
 
Using some wood filler, the Chaffing fish was sanded smooth. I then brushed clean the mast and used alcohol to get rid of any residual debris.
IMG_0344.jpeg
Mast reenforcing bands were next to be applied to the mast. The instructions would have you use 1/64 X 1/16 brass strip but I used a simpler method that Tom Culb did in his build log. I used 1/16" auto pin-striping tape. Tom used a tape called chart pack which is probably similar. It is easy to apply and cuts very easily with a blade. Once it was applied I burnished it down. I used two layer to provide some thickness.
IMG_0345.jpeg
 
I have seen build logs where shipwrights have used cardboard strips or masking tape to represent these bands, normally colored black.
The pin-striping tape can be bought in many different colors. I just happened to have a roll of white, and later on the instructions will have you paint the whole mast assembly white.
 
The "rings" on the mast were finally installed.
IMG_0354.jpeg

The next step is to place the cheeks that will hold the fighting top. In order to make sure the cheeks are in the correct place, I decided to make more of the fighting top so I could fit it on the mast and make adjustments to the cheeks. The cross and terstle tree on the bottom of the fighting top were 4 laser cut parts that fit exactly. After cleaning them up I glues the forward crosstree onto the fighting top. Then using the trestle trees spacers I glued the rear crosstrees into position.
IMG_0355.jpeg

The trestle trees have what the instruction call "thumb cleats" and on the parts are identified as "cheek cleats' to make things confusing. These are basically pulleys. They have metal sheaves inside. You have to be a bit careful unpacking out the sheaves as there are others slightly smaller that will be used later on, The smaller one is on the bottom in the picture below.
IMG_0357.jpeg

You are to drill holes in these thumb cleats in order to put small nails through them and the sheaves to make a pulley. When you do this I would suggest you place a sheave in the thumb cleat when you drill the hole to prevent it from breaking, (Ask me how I know this :rolleyes:) It is probably a good idea to coat these thumb cleats with some thin CA first in order to make them more resistant to breaking, Be that as it may, the holes were drilled.
IMG_0359.jpeg

The thumb cleats actually came out ok and the sheaves rotate freely.
IMG_0363.jpeg
 
Two bolsters were also to be fitted onto the trestle trees. These were laser cut pieces and had to be made quarter round. Using the sanding drum of my nail drill made this very easy to do.

IMG_0362.jpeg

The thumb cleats were glued onto the trestle trees and test fitted onto the fighting top along with the bolsters.
IMG_0364.jpeg

There is also another, smaller bolster that sits on top of the fighting top. It is also shown on the building plans. There was no laser cut piece for this that I could find so I made one from the numerous scrap pieces available.

IMG_0366.jpeg
 
Last edited:
After the mast chocks and Mast fairlead were attached as shown in the plans, the mast and the fighting top were covered with a coat of sanding sealer.
IMG_0368.jpeg

At this point I noticed there were two sizes of mast chocks supplied. I believe the smaller one (the ones I installed naturally) are for the upper masts. On the laser cut parts both sets of Chocks are labeled "Mast Chocks" seemingly to help confuse you. Luckily the smaller chocks snapped off cleanly and the larger chocks were installed. The also want you to install the boarding pike racks. However these are fragile pieces and I will assemble them along with the boarding pike separately and place them on the mast later on in the build.

The top of the fighting top was painted tamyia light gray. After carefully painting the entire surface I noticed they want you to keep the rear surface unpainted in order to later install a guard rail. After the paint dried I was easily able to remove the paint from that part using my little mini drum sander,

IMG_0371.jpeg

Using 1/32 X 1/8" strip I made the edge batten which goes against 3 sides of the fighting top. As suggested I placed the planks in hot water for a few minutes. I then wiped them down with Windex. The ammonia in Windex seems to make the wood more pliable. Going slowly I bent the piece around the fighting mast and held it in place to dry using rubber bands.

IMG_0372.jpeg
 
Last edited:
Good afternoon Rob. I had some catching up to do do I wasn’t going to send a gazillion likes;). Suffice to say you are making wonderful progress- I like the use of tape for the mast bands, it gives a nicer finish than brass strips IMHO.Cheers Grant
 
Back
Top