Starta detta
USS Bonhomme Richard 1/48 Section-Pear version by Larsa
- Thread starter Larsa
- Start date
- Watchers 8
-
- Tags
- bonhomme richard unicorn
Hi ,you need to hit the to top "Full image" button like on this image below to get full images
Thanks,learning
you have all the tutorials here
Welcome aboard @Larsa, and many thanks for starting a build log. We have a few build logs with the same kit. If you don't mind, please take a look.
From John (@neptune)
From Uwe (@Uwek )
By Carlosys (@carlosys )
Happy modeling
From John (@neptune)
USS BONHOMME RICHARD - POF - Cross Section in Cherry - 1:48 - by neptune,
I have had these kits for approx two years now and I have been holding off starting them, once Uwe started his build log it got my juices flowing so here goes, and by the way I will be building two of them at the same time, I will post some pics of the kit contents in awhile, but for now, This...
shipsofscale.com
From Uwe (@Uwek )
USS BONHOMME RICHARD - POF - Cross Section in Pear - 1:48 - by Uwe
Yesterday I started the first activities on my section model - in order to warm up At the end it should look like this a kit review you can find here...
shipsofscale.com
By Carlosys (@carlosys )
USS BONHOMME RICHARD - POF - Cross Section in Cherry - 1:48 - by carlosys [COMPLETED BUILD]
Hi everyone. It seems that this model is fashionable in the forum so I will collaborate with my progress to help all the colleagues who are doing it too. For my part, I will learn from your work. The first steps do not have much mystery. In my case, I am deck by deck in order to adjust each...
shipsofscale.com
Happy modeling
Larsa.is this going to be your build log? I can move this thread to the kit build log section
Hi,i am not so good at building log´s,but i try my best
G'day Lara, welcome to the forum, I look forward to seeing your build of the cross section,
Best regards John,
Best regards John,
Also from my side a warm welcome. I am looking forward to see your section in this log
I think this will work,not glued on place yet
Last edited by a moderator:
Whats the easyiest/best way to simulate nailholes/plugs in a plank?
Have to find a way! have never build that big scale(1/48) that need it!
Have to find a way! have never build that big scale(1/48) that need it!
It depends on the necessary size of the original nail, treenail or bolt!
So the first question to you: for which element on the section you want to simulate the "nail".
if you are looking for the inside furniture:
These would be only "normal" nails to fix the wooden bord against a smaller pillar - so the head of a used nail would be in reality only maybe 2cm - in scale 1:48 it would be only 0,4mm in diameter.
Because of this very small size I decided in my section only to punch a small hole with a scriber (german: Anreißnadel)
and this is the result:
USS BONHOMME RICHARD - POF - Cross Section in Pear - 1:48 - by Uwe
Looking very good Uwe, did you use the pre cut parts for the bottom of the shot locker, I didn't realise what they were for until after I had planked it, Best regards John, Thanks for the hint. Can you show which part you mean? Please
shipsofscale.com
so therefore it is only a small hole, you can see the difference only when you very very close.
If needed you can easily close the hole with some wood paste, like the above mentioned (available in different colors), and can be sanded afterwards flash with the plank
Looking very good - so hope to see more often much more from your project 
Thanks Uwe,i will try my bestLooking very good - so hope to see more often much more from your project
Have a good Eastern
Hallo Larsa,
Can you Show us some Progress on your section? Or is it on hold in Moment ?
Maybe you can Show us some Update.....
Can you Show us some Progress on your section? Or is it on hold in Moment ?
Maybe you can Show us some Update.....
