-
SUBSCRIBE TO SHIPS IN SCALE TODAY!
The beloved Ships in Scale Magazine is back and charting a new course for 2026!
Discover new skills, new techniques, and new inspirations in every issue.
NOTE THAT OUR NEXT ISSUE WILL BE July/August 2026 -
Win a Free Custom Engraved Brass Coin!!!
As a way to introduce our brass coins to the community, we will raffle off a free coin during the month of August. Follow link ABOVE for instructions for entering.
USS Constitution - Model Shipways
- Thread starter Der Alte Rentner
- Start date
- Watchers 20
Oh for Pete's sake... What happened here?
Everything confirmed to plan, yet the fairlead is sitting on the scrollwork.
Three options suggest themselves.
1. Leave it alone (by far my favorite!)
2. Remake the fairlead and locate it further forward, say 3.15mm (1/8")
3. Lop off the locating tenon at the aft end of the bowsprit and drop that end lower to increase the angle slightly
and this was my third fairlead of the day. I had issues drilling the 10.5mm hole. That was resolved by setting up the drill press vs. drilling by hand.
Before making the fairlead and chocks, I wanted to see how much effort would be involved in rigging the gammoning "chain" (I opted for rope). It turned out not to be too much of a hassle. But, off it came to start adding the as yet unmade components.
I did the prep work of determining the correct number of holes (7 according to MS plans. 8 according to Bob Hunt). 9 according to Marquardt.
Since Mustafa had seven, I opted for the "consensus" view).
Then I marked the boxwood blank and began fabrication. Drat! I don't have photos of the next steps! Well, if I choose option 2 above, I'll have a second chance at documenting the making of the fairlead...
Note: for some things (like cutting the chocks to length), old school is still the best.
Everything confirmed to plan, yet the fairlead is sitting on the scrollwork.
Three options suggest themselves.
1. Leave it alone (by far my favorite!)
2. Remake the fairlead and locate it further forward, say 3.15mm (1/8")
3. Lop off the locating tenon at the aft end of the bowsprit and drop that end lower to increase the angle slightly
and this was my third fairlead of the day. I had issues drilling the 10.5mm hole. That was resolved by setting up the drill press vs. drilling by hand.
Before making the fairlead and chocks, I wanted to see how much effort would be involved in rigging the gammoning "chain" (I opted for rope). It turned out not to be too much of a hassle. But, off it came to start adding the as yet unmade components.
I did the prep work of determining the correct number of holes (7 according to MS plans. 8 according to Bob Hunt). 9 according to Marquardt.
Since Mustafa had seven, I opted for the "consensus" view).
Then I marked the boxwood blank and began fabrication. Drat! I don't have photos of the next steps! Well, if I choose option 2 above, I'll have a second chance at documenting the making of the fairlead...
Note: for some things (like cutting the chocks to length), old school is still the best.
Last edited:
Fabulous modeling Peter.
I know this feeling way too often- it’s the modeling gods I tell you….… Cheers Grant
2026 July 02: Fairlead fail corrected!
I chose option 2 above: Remake the fairlead and locate it further forward, say 3.15mm (1/8"). So, here’s the documentation on making the fairlead in excruciating detail. In case it’s unclear in the middle photo in the top row below, I used double sided tape to affix the boxwood blank onto a piece of scrap wood – thus I eliminate ragged edges on the flip side of the piece after drilling.
I used double sided tape to affix the 1.56mm basswood blank to a backing board - thus eliminating tear-out on the back side of the drilled holes.
I tried this using a hand drill three times before figuring out there's a reason I got a drill press with fence.
I used a piece of rolled up sandpaper to fine tune the inner arc on the fairlead.
test fit...
Fine tune the bulk of the fairlead (leaving the final trimming to good old fashioned sanding stick.
The old fairlead needed to be chiseled off.
and here's the new fairlead in its new position.
I chose option 2 above: Remake the fairlead and locate it further forward, say 3.15mm (1/8"). So, here’s the documentation on making the fairlead in excruciating detail. In case it’s unclear in the middle photo in the top row below, I used double sided tape to affix the boxwood blank onto a piece of scrap wood – thus I eliminate ragged edges on the flip side of the piece after drilling.
I used double sided tape to affix the 1.56mm basswood blank to a backing board - thus eliminating tear-out on the back side of the drilled holes.
I tried this using a hand drill three times before figuring out there's a reason I got a drill press with fence.
I used a piece of rolled up sandpaper to fine tune the inner arc on the fairlead.
test fit...
Fine tune the bulk of the fairlead (leaving the final trimming to good old fashioned sanding stick.
The old fairlead needed to be chiseled off.
and here's the new fairlead in its new position.
A nice solution, Peter. And I think the right one...
I love to follow your problem solving skills. Your Conny will be a masterpiece when finished. Great job!
2026 July 03: Jibboom and flying jibboom.
Nothing by way of process photos today. There were a couple of details needing attention on the jibboom. A sheave needed to be added at the forward end, as did a third hole. Also, the very end needed to be reshaped to accommodate the “iron” ring which will hold part of the flying jibboom. I’ve shown enough lathe work in shaping spars and mill work to simulate sheaves, that I didn’t bother with the details of the construction of the flying jibboom.
The flying jibboom should be the last item requiring lathe work on this model. Here it is attached to the jibboom and bowsprit cap. I got so wrapped up in the brasswork, that I forgot to take pictures of the flying jibboom irons – that connected double circle in the plan photo above. Basically, I just bent some brass strip around an 1/8” drill bit to get me the loops. Some tweaking with pliers, and the application of some 5-minute epoxy, was all that was required at that end. To affix the other end of the flying jibboom to the cap, I made a staple, drilled a couple of holes, applied some C/A glue and drove the staple home with a pair of pliers.
Here’s everything in place. The cap has not been glued in, so I can remove the jibboom, flying jibboom assembly to store it safely until I’m done rigging everything aft of the cap.
Nothing by way of process photos today. There were a couple of details needing attention on the jibboom. A sheave needed to be added at the forward end, as did a third hole. Also, the very end needed to be reshaped to accommodate the “iron” ring which will hold part of the flying jibboom. I’ve shown enough lathe work in shaping spars and mill work to simulate sheaves, that I didn’t bother with the details of the construction of the flying jibboom.
The flying jibboom should be the last item requiring lathe work on this model. Here it is attached to the jibboom and bowsprit cap. I got so wrapped up in the brasswork, that I forgot to take pictures of the flying jibboom irons – that connected double circle in the plan photo above. Basically, I just bent some brass strip around an 1/8” drill bit to get me the loops. Some tweaking with pliers, and the application of some 5-minute epoxy, was all that was required at that end. To affix the other end of the flying jibboom to the cap, I made a staple, drilled a couple of holes, applied some C/A glue and drove the staple home with a pair of pliers.
Here’s everything in place. The cap has not been glued in, so I can remove the jibboom, flying jibboom assembly to store it safely until I’m done rigging everything aft of the cap.
Exquisite modeling, Peter. That wishbone is pretty impressive - best to put it away for safe keeping!
Thanks Jon,
What exactly is happening at the forward end of the bees in the first photo? I thought that was an eyebolt, but closer inspection suggests otherwise. Got a picture of the upper face of the bees?
What exactly is happening at the forward end of the bees in the first photo? I thought that was an eyebolt, but closer inspection suggests otherwise. Got a picture of the upper face of the bees?
So, not a pair of eyebolts after all.
Just a small section of chain? connecting the bobstays? At least now I know what the indentations at the forward end of the bees are for.
Also interesting to note the different numbers of ropes passing through the fairleads in the 2nd and 3rd photos.
Just a small section of chain? connecting the bobstays? At least now I know what the indentations at the forward end of the bees are for.
Also interesting to note the different numbers of ropes passing through the fairleads in the 2nd and 3rd photos.
- Joined
- Oct 9, 2020
- Messages
- 2,381
- Points
- 488
In regards to the dolphin striker, it seems that we have a number of holes to drill, and I see them in the photo of the actual one, but only the top holes are used. I wonder what the purpose of the other holes are. I am tempted to not even drill those bottom holes especially since the bottom part of the striker is so fragile.
Last edited:
Every time I have that thought, and express it here, someone posts a photo showing exactly where that hole, or sheave, or eyebolt is being used. Better to have it and not need it, then need it and not have it. For what it's worth, if you used boxwood to make the striker, you wouldn't have concerns. It's pretty sturdy stuff.
- Joined
- Oct 9, 2020
- Messages
- 2,381
- Points
- 488
I don't get it. One pic they are 't used and another they are. Anyways, I'll drill them.