HI HEINRICH THAT WAS A DRY FIT, I DO HAVE WIDER CLAMPS, I HAVE NOW GLUED THE REAR FRAME PARTS TOGETHER HERE IS PICTURE I AM VERY CONCERNED ABOUT BREAKAGE UNTIL THE 2 HALVES ARE JOINED SO I USED A SCRAP PIECE OF WOOD TO HOLD IT TILL READY, WHAT DO YOU THINK, LET ME KNOW. GOD BLESS STAY SAFE YOU AND YOURS DON
Attachments
HEINRICH I AM REALLY GETTING BAD THIS MESSAGE SAT FOR 10 MINUTES BEFORE I RELIZED I DID PRESS (POST REPLY) LOL, LOL, AGE, LET ME KNOW WHAT YOU THINK I WAS WONDERING IF I SHOULD DO MORE FRAMES REAR SECTIONS ONLY UNTIL I KNOW WHAT TO DO WITH THE FRONTS AND WITH THE BEVELS, LIKE FRAME NO. 32 TO STERN WHERE NO BEVELS ARE JUST WONDERING. GOD BLESS STAY SAFE YOU AND YOURS DON
- Joined
- Jan 9, 2020
- Messages
- 10,424
- Points
- 938
Don I leave the frames clamped over the joints on the paper - without touching them - for at least 4 hours. I see on your picture that you have removed the frame from the paper. Was this after the 4 hour-period? Wait at least 4 hours before you do this. We will worry about the other frames when the rear of frame #31 is dry and you tell me it is dry.
HEINRICH 5 HOURS PLUS, WILL LET YOU KNOW TONIGHT BEFORE I GO TO BED ABOUT 9:00 PM USA TIME, YOU CAN TELL ME TOMORROW IF YOY ARE BUSY, I WILL LEAVE IT CLAMPED TO THE SPARE BOARD. GOD BLESS STAY SAFE ALL DON
OK HEINRICH WILL DO. GOD BLESS STAY SAFE YOU AND ANNA DON
GOOD MORNING TO YOU FRIEND, I AM READY TO PROCEDE WHENEVER YOU CAN LET ME HERE. GOD BLESS YOU AND YOURS STAY SAFE DON
- Joined
- May 26, 2020
- Messages
- 181
- Points
- 113
I like those clamps. Mine are all the short type.
will have to get some.
will have to get some.
- Joined
- Jan 9, 2020
- Messages
- 10,424
- Points
- 938
Don if you look at your picture,
1. You can clearly see that the frame is not lined up with the drawing. I have indicated one point with the red arrow, but that gap is right around the frame.
2. You have only clamped over one joint like I suggested. I have marked that with a red tick.
3. As we look at the picture - the joint on the left has not been clamped. I have marked that with a cross.
1. You can clearly see that the frame is not lined up with the drawing. I have indicated one point with the red arrow, but that gap is right around the frame.
2. You have only clamped over one joint like I suggested. I have marked that with a red tick.
3. As we look at the picture - the joint on the left has not been clamped. I have marked that with a cross.
HI HEINRICH HERE ARE THE 2 PICTURES FRONT AND BACK THE FRAME ON THE PAPER WAS A RE POSITION AFTER I REMOVED IT FROM THE ORIGINAL WILL SHOW IT AGAIN AND IF YOU LOOK BACK ALL THE JOINTS WERE CLAMPED AFTER GLUEING I WILL TRY TO FIND THE PICTURE IT IS ON THIS LOG. GOD BLESS STAY SAFE YOU AND YOURS DON
Attachments
HI HEINRICH I APOLIGIZE FOR THEWAY PICTURES WERE TAKIN HARD TO GET IT SITTING DOWN THESE ARE PICTURES JUST TAKEN POSITIONED ON THE ONE THAT IT WAS GLUED TO THE ONE YOU SAW WAS NOT DONE ON THE ONE I USED FROM NOW ON WILL POST A BEFORE AND AFTER GLUEING HOPE THIS ONE IS RIGHT MY APOLIGIZES. GOD BLESS STAY SAFE YOU AND YOURS DON
TERRY THESE CLAMPS I GOT AT MENARDS, I HAVE ORDERED SOME BESSEY CLAMPS FROM WALL MART THEY ARE EXPENSIVE $6.00 EA HAVE A 3 INCH THROAT THESE CAME RECOMENDED BY DOC BLAKE ON HIS GRANDO X SECTION LOG ON SOS. GOD BLESS STAY SAFE ALL DON