Hello Tony,
Thx for the info but I would like to get your photo's: I solved it meanwhile.
An update on my part: today I finished the Transom as well as completed the Main Wale.
You will see that I (see stern) sanded the Main Wale flush with the Transom....
Everything has also been roughly sanded...in anticipation of the fine work.
I read in your previous message that you were going to figure out how to place the Main Wale.
I did it the following way:
The main wale consists of 7 strips (1/8" x 3/32"). I measured the distance on each bulkhead (sheet 3) and divided it by 7. This distance is the width of each strip on the respective bulkhead. So it's just a matter of sanding the strips to the correct width.
Special attention is needed for the Stern: here the strips are each 3/64" wide and should be bent slightly.
The same applies for the bow. I applied three strips
bulkhead F-K
bulkhead L-Stern
bulkhead A-F
![1694621020281.png 1694621020281.png](https://shipsofscale.com/sosforums/data/attachments/378/378227-408eb6a407136aa9d276088d97419918.jpg?hash=QI62pAcTaq)
![Tony70.jpg Tony70.jpg](https://shipsofscale.com/sosforums/data/attachments/378/378223-925962e806b9a0f760987573e0dd7e6e.jpg?hash=klli6Aa5oP)
![Tony71.jpg Tony71.jpg](https://shipsofscale.com/sosforums/data/attachments/378/378224-d390b4a7f3aa291b0c2022e3894bbc65.jpg?hash=05C0p_OqKR)
![Tony72.jpg Tony72.jpg](https://shipsofscale.com/sosforums/data/attachments/378/378225-de62ec7eb6e09cc9e7a26906b1fbcb56.jpg?hash=3mLsfrbgnM)
![Tony74.jpg Tony74.jpg](https://shipsofscale.com/sosforums/data/attachments/378/378226-925962e806b9a0f760987573e0dd7e6e.jpg?hash=klli6Aa5oP)
Thx for the info but I would like to get your photo's: I solved it meanwhile.
An update on my part: today I finished the Transom as well as completed the Main Wale.
You will see that I (see stern) sanded the Main Wale flush with the Transom....
Everything has also been roughly sanded...in anticipation of the fine work.
I read in your previous message that you were going to figure out how to place the Main Wale.
I did it the following way:
The main wale consists of 7 strips (1/8" x 3/32"). I measured the distance on each bulkhead (sheet 3) and divided it by 7. This distance is the width of each strip on the respective bulkhead. So it's just a matter of sanding the strips to the correct width.
Special attention is needed for the Stern: here the strips are each 3/64" wide and should be bent slightly.
The same applies for the bow. I applied three strips
bulkhead F-K
bulkhead L-Stern
bulkhead A-F
![1694621020281.png 1694621020281.png](https://shipsofscale.com/sosforums/data/attachments/378/378227-408eb6a407136aa9d276088d97419918.jpg?hash=QI62pAcTaq)
![Tony70.jpg Tony70.jpg](https://shipsofscale.com/sosforums/data/attachments/378/378223-925962e806b9a0f760987573e0dd7e6e.jpg?hash=klli6Aa5oP)
![Tony71.jpg Tony71.jpg](https://shipsofscale.com/sosforums/data/attachments/378/378224-d390b4a7f3aa291b0c2022e3894bbc65.jpg?hash=05C0p_OqKR)
![Tony72.jpg Tony72.jpg](https://shipsofscale.com/sosforums/data/attachments/378/378225-de62ec7eb6e09cc9e7a26906b1fbcb56.jpg?hash=3mLsfrbgnM)
![Tony74.jpg Tony74.jpg](https://shipsofscale.com/sosforums/data/attachments/378/378226-925962e806b9a0f760987573e0dd7e6e.jpg?hash=klli6Aa5oP)